一.硫化橡膠塑料擊穿電壓試驗儀適用范圍
電壓擊穿試驗儀滿足GB1408-2006 絕緣材料電氣強度試驗方法，GB/T1695-2005硫化橡膠工頻電壓擊穿強度和耐電壓強度試驗 GB/T3333 電覽紙工頻電壓擊穿試驗方法 HG/T 3330絕緣漆漆膜擊穿強度測定法 GB12656 電容器紙工頻電壓擊穿試驗方法及ASTM D149 標準要求.主要適用于固體絕緣材料如：塑料、薄膜、樹脂、云母、陶瓷、玻璃、絕緣漆等介質在工頻電壓或直流電壓下?lián)舸?qiáng)度和耐電壓時間的測試。
二.硫化橡膠塑料擊穿電壓試驗儀主要技術參數：
1）輸入電壓：交流 220V ；輸出電壓： 交流 0--50KV ，直流 0—50kv ；電器容量：5KVA；能進行直流和交流試驗；
2）有透明防護罩，升壓速度10-5000V/s可調，可以實現均勻升壓、梯度升壓、耐壓升壓、連續升壓、逐級升壓、手動升壓等功能，要求輸入交流220V，分別輸出交流、直流0-50kV，分級為0-5kV、0-10kV、0-20kV、0-50kV
3）準確度1%，有自動保護，帶電腦和打印機，可記錄和打印試驗值和圖表。
4）主要用于絕緣紙及紙板、層壓板、絕緣管、線棒、塑料、薄膜、柔軟復合材料、浸漬樹脂、橡膠、絕緣膠、陶瓷等絕緣材料的擊穿電壓、電氣強度、耐電壓實驗，配2套相應電極。
5）適用標準：GB1408-2006 、GB/T 507-2002、GB/T1695-2005 DL429.9-91、GB/T3333
三.硫化橡膠塑料擊穿電壓試驗儀安全保護
試驗在試驗箱中進行，試驗箱門打開時電源加不到高壓變壓器輸入端，即高壓側無電壓。100KV測試設備高壓電極距離試驗箱壁的zui近距離大于370mm，50KV測試設備高壓電極距離試驗箱壁的zui近距離大于250mm，試驗時即使人接觸箱壁也不會有危險。
設備要安裝單獨的保護地線。接保護地線，主要是減少試樣擊穿時對周圍產生的較強的電磁干擾。也可避免控制計算機失控。
該試驗設備的電路設有多項保護措施，主要有：過流保護、失壓保護、漏電保護、短路保護、直流試驗放電報警等。
直流試驗放電報警功能:在設備做完直流試驗時,當開啟試驗門時設備會自動報警,直至使用設備上的放電裝置放電后報警會自動取消.（注：因?yàn)橹绷髟囼?yàn)后不放電會危險到人身安全,不能直接拿取電極,起到提醒使用人員放電以免造成人身傷害）。
試驗放電裝置，隨主機為一體化，改進了以往單獨配備一根放電桿的功能。
六級高壓安全斷電控制：①總電源開關②高壓斷電開關（鑰匙開關）③調壓器復位開關④試驗箱門安全開關⑤高壓變壓器輸入側限流空開⑥漏電保護開關
四、硫化橡膠塑料擊穿電壓試驗儀?設備主要配置
1 試驗主機 （ 一臺 ） 2 高壓發生器50kv （ 一套 ）
3 試驗電極 二套 (國標1408.1) 4 試驗油箱 （一只 ）
5 放電系統 （一套 ） 6 控制系統 （一套 ）
7 數據采集系統 （ 一套 ） 8 試驗軟件 （一套 ）
9 計算機 （一套 ） 可選 PC/EPC 10 噴墨打印機 （ 一臺 ） 選購
11 產品使用說明書 （一份 ） 12 計量證書（航天院（ 一份） 選購
13 產品合格證 （一份 ） 14電子穩壓器 （ 一臺）
15隨機清單 （ 一份） 16絕緣手套 （一套 ）
17絕緣腳墊 2米 選購 18藍牙發射器 （ 一支 ） 選購
19藍牙接收器 一支 選購
產品保修售后服務承諾：
一、安裝調試：協助試驗機的安裝，負責試驗機的運輸、調試。
二、驗收標準：試驗機按訂貨技術附件進行驗收。終驗收在買方進行，對用戶提供的試樣進行試驗，并提供測試報告。
三、培訓：安裝調試同時，在儀器操作現場一次性免費培訓操作人員2-3名，該操作人員應是由需方選派的長期穩定的員工，培訓后能夠?qū)υO(shè)備基本原理、軟件使用、操作、維護事項理解和應用，使人員能夠獨立操作設備對樣品進行檢測、分析，同時能進行基本的維護。
四、軟件升級：終生免費提供新版本控制軟件。
五、保修：
1、設備保修兩年，終身售后服務，一年內非人為損壞的零部件免費更換，保修期內接到用戶邀請后，zui遲響應時間為2小時內，在與用戶確認故障后，我公司會在48小時內派工程師到達現場進行免費服務，盡快查清故障所在位置和故障原因，并向用戶及時報告故障的原因和排除辦法。
2、保修期內人為損壞的零部件按采購（加工）價格收費更換。
3、保修期外繼續為用戶提供優質技術服務，在接到用戶維修邀請后3天內派工程師到達用戶現場進行維修。并享有優惠購買零配件的待遇?！?br />4、傳感器過載及整機電路超壓損壞不在保修范圍內。
六、售后管理：
我公司實現計算機化管理，實行客戶定期回訪制度，定期復查設備的工作情況，定期指導用戶對設備進行保養和檢測，以便設備正常運轉，跟蹤客戶的設備使用情況，以便及時對設備進行維護
The scope of application of testing apparatus for testing insulation properties of insulating materials
The breakdown voltage tester to meet the test method of GB1408-2006 electrical strength of insulating materials, GB/T1695-2005 vulcanized rubber voltage breakdown strength and voltage endurance test of GB/T3333 electric cable paper voltage breakdown testing method of HG/T 3330 insulation paint film breakdown strength determination method of GB12656 capacitor voltage breakdown testing method and ASTM D149 standard. Mainly applicable to solid insulation materials such as: plastic, film, resin, mica, ceramic, glass, insulating paint and other media in the frequency of the voltage or DC voltage breakdown strength and voltage withstand the test of time.
Two. The main technical parameters of the test apparatus for testing insulation properties of insulating materials:
1) input voltage: AC 220V; output voltage: AC 0--50KV, DC 0 - 50kV; electrical capacity: 5KVA; DC and AC test;
2) with a transparent protective cover, boost 10-5000V/s speed adjustable, can achieve uniform pressure, pressure gradient, pressure boost, continuous, boost step, manual boost function, input AC 220V, output AC and DC 0-50kV, 0-5kV, 0-10kV, 0-20kV grade, 0-50kV
3) accuracy 1%, automatic protection, with computers and printers, can record and print test values and charts.
4) mainly used for insulation paper and paperboard, laminated board, insulating tube, wire rod, plastic, thin film, soft composite material, impregnating resin, rubber, insulating rubber, ceramics and other insulating materials breakdown voltage, electrical strength, withstand voltage test, equipped with 2 sets of corresponding electrodes.
5) applicable standards: GB1408-2006, GB/T 507-2002, GB/T1695-2005 DL429.9-91, GB/T3333
Three. Safety protection of insulation performance tester for insulating materials
The test is carried out in the test box, and the power supply can not be added to the input end of the high voltage transformer when the test box door opens, that is, the high voltage side has no voltage. The closest distance between the 100KV test equipment and the high-pressure electrode distance test box wall is greater than 370mm. The closest distance between the 50KV test equipment and the test chamber wall is more than 250mm. Even when people are in contact with the wall of the test box, there will be no danger.
The equipment should be equipped with a separate protective ground wire. The protective ground wire is mainly to reduce the strong electromagnetic interference to the surrounding when the sample is broken down. It can also avoid controlling computer out of control.
The circuit of the test equipment has many protective measures, including overcurrent protection, loss of voltage protection, leakage protection, short circuit protection, DC test discharge alarm, etc.
DC discharge test alarm function: in the equipment finished DC test, when open the door will automatically alarm test device, discharge device used on the device after discharge until the alarm will automatically be cancelled. (Note: because the DC test not put electricity danger to personal safety, can not be directly taken to remind users electrode. Discharge to avoid personal injury).
The test discharge device, which is integrated with the mainframe, improves the function of a single discharge pole in the past.
Six stage high pressure safety power-off control: power switch, high voltage disconnecting switch (key switch) the regulator reset switch the test box door safety switch, high voltage transformer input side of the open limit flow leakage protection switch
Four. The main configuration of testing equipment for insulating material insulation performance tester
1 test host (one) 2 high voltage generator 50kV (one set)
3 test electrode two sets (national standard 1408.1) 4 test oil tank (one)
5 discharge system (one set) 6 control system (one set)
7 data acquisition system (one set) 8 test software (one set)
9 computer (one) optional PC/EPC 10 inkjet printer (one)
11 product instructions (one) 12 measurement certificate (Space Institute (one))
13 product certificate (one) 14 electronic stabilizer (one)
15 random list (one) 16 insulating gloves (one set)
17 insulated pads and 2 meters for 18 Bluetooth launchers (one)
19 Bluetooth receiver
Product warranty after service commitment:
1. Install and debug: assist the installation of the test machine, and be responsible for the transportation and commissioning of the test machine.
Two. Acceptance criteria: the test machine is accepted according to the order technical accessories. The final acceptance is carried out by the buyer, the sample is tested by the user and the test report is provided.
Three, training: installation and commissioning at the same time, the instrument operation on-site one-time free training 2-3, the operating personnel shall be appointed by the long-term stability of the staff training to the equipment basic principle, software use, operation, maintenance issues, understanding and application, so that the personnel can operate the equipment independently to detect samples, at the same time can carry on the basic analysis and maintenance.
Four, software upgrade: free of charge new version control software for life.
Five. Warranty:
1, the equipment warranty of two years, lifelong customer service service, within one year of non-human damage free replacement parts, the warranty period the user received the invitation, the latest response time is 2 hours, with the user to confirm the fault, our company will send engineers arrived at the scene for free within 48 hours of service, to identify the fault location and the cause of the fault as soon as possible, and timely report to the user fault and maintenance.
2, the parts of the insured during the warranty period are changed according to the price of purchase (processing).
3, the warranty period to continue to provide quality technical services for the users, send within 3 days of receiving maintenance after inviting users
